最近一直Linux内核的时候加载yaffs文件老是不成功

躺在天使的翅膀上 · 发表于 2014-9-16 13:43:50

OK6410-A开发板,最近一直Linux内核的时候加载yaffs文件老是不成功，出现了一下
Freeing init memory: 116K
Failed to execute /linuxrc. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
这样的问题，说找不到init ，但是我用busybox制作的文件里面有init，都迷茫一两个星期了求大神们指点一下？万分感谢了！

U-Boot 2013.04-rc1 (Sep 16 2014 - 11:16:49) for SMDK6410

CPU:     S3C6410@533MHz

         Fclk = 533MHz, Hclk = 133MHz, Pclk = 66MHz (ASYNC Mode)

Board:   SMDK6410

DRAM: 256 MiB

WARNING: Caches not enabled

Flash: 0 Mib

NAND: 2048 MiB

MMC:   Samsung Host Controller: 0

*** Warning - bad CRC, using default environment

In:    serial

Out:   serial

Err:   serial

Net:   dm9000

Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x500000

5242880 bytes read: OK

## Booting kernel from Legacy Image at 50008000 ...

   Image Name:   Linux-3.8.3

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    1647608 Bytes = 1.6 MiB

   Load Address: 50008000

   Entry Point: 50008040

   Verifying Checksum ... OK

   XIP Kernel Image ... OK

OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.8.3 (root@meijian-virtual-machine) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #25 Tue Sep 16 11:28:47 CST 2014
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S3C64XX: PLL settings, A=533000000, M=533000000, E=24000000
S3C64XX: HCLK2=266500000, HCLK=133250000, PCLK=66625000
mout_apll: source is fout_apll (1), rate is 533000000
mout_epll: source is epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 533000000
usb-bus-host: source is clk_48m (0), rate is 48000000
irda-bus: source is mout_epll (0), rate is 24000000
CPU: found DTCM0 8k @ 00000000, not enabled
CPU: moved DTCM0 8k to fffe8000, enabled
CPU: found DTCM1 8k @ 00000000, not enabled
CPU: moved DTCM1 8k to fffea000, enabled
CPU: found ITCM0 8k @ 00000000, not enabled
CPU: moved ITCM0 8k to fffe0000, enabled
CPU: found ITCM1 8k @ 00000000, not enabled
CPU: moved ITCM1 8k to fffe2000, enabled
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: noinitrd root=/dev/mtdblock2    rootfstype=yaffs2 init=/linuxrc     console=ttySAC0,115200
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
__ex_table already sorted, skipping sort
Memory: 256MB = 256MB total
Memory: 256400k/256400k available, 5744k reserved, 0K highmem
Virtual kernel memory layout:
    vector : 0xffff0000 - 0xffff1000   (   4 kB)
    DTCM    : 0xfffe8000 - 0xfffec000   ( 16 kB)
    ITCM    : 0xfffe0000 - 0xfffe4000   ( 16 kB)
    fixmap : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
    lowmem : 0xc0000000 - 0xd0000000   ( 256 MB)
    modules : 0xbf000000 - 0xc0000000   ( 16 MB)
      .text : 0xc0008000 - 0xc02d8e14   (2884 kB)
      .init : 0xc02d9000 - 0xc02f657c   ( 118 kB)
      .data : 0xc02f8000 - 0xc0327a80   ( 191 kB)
       .bss : 0xc0328000 - 0xc035973c   ( 198 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:246
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Console: colour dummy device 80x30
Calibrating delay loop... 353.89 BogoMIPS (lpj=1769472)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x5021a6d8 - 0x5021a734
devtmpfs: initialized
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
OK6410: Option string ok6410=0
OK6410: selected LCD display is 480x272
s3c64xx_dma_init: Registering DMA channels
PL080: IRQ 73, at d0846000, channels 0..8
PL080: IRQ 74, at d0848000, channels 8..16
S3C6410: Initialising architecture
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NetWinder Floating Point Emulator V0.97 (double precision)
ROMFS MTD (C) 2007 Red Hat, Inc.
BeFS version: 0.9.3
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3c-fb s3c-fb: window 0: fb
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s3c6400-uart.0: ttySAC0 at MMIO 0x7f005000 (irq = 69) is a S3C6400/10
console [ttySAC0] enabled
s3c6400-uart.1: ttySAC1 at MMIO 0x7f005400 (irq = 70) is a S3C6400/10
s3c6400-uart.2: ttySAC2 at MMIO 0x7f005800 (irq = 71) is a S3C6400/10
s3c6400-uart.3: ttySAC3 at MMIO 0x7f005c00 (irq = 72) is a S3C6400/10
brd: module loaded
loop: module loaded
S3C NAND Driver, (c) 2008 Samsung Electronics
dev_id == 0xd5 select s3c_nand_oob_mlc
****Nandflash:ChipType= MLC ChipName=samsung-K9GAG08U0D************
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit), 2048MiB, page size: 4096, OOB size: 218
Driver must set ecc.strength when using hardware ECC
Creating 4 MTD partitions on "NAND 2GiB 3,3V 8-bit":
0x000000000000-0x000000100000 : "Bootloader"
0x000000100000-0x000000600000 : "Kernel"
0x000000600000-0x00000ce00000 : "File System"
0x00000ce00000-0x000080000000 : "User"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
s3c2410-ohci s3c2410-ohci: init err (00000000 0000)
s3c2410-ohci s3c2410-ohci: can't start s3c24xx
s3c2410-ohci s3c2410-ohci: startup error -75
s3c2410-ohci s3c2410-ohci: USB bus 1 deregistered
s3c2410-ohci: probe of s3c2410-ohci failed with error -75
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: mmc_busclk.0 (133250000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_busclk.2 (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: mmc_busclk.0 (133250000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_busclk.2 (24000000 Hz)
mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc0: mmc_rescan_try_freq: trying to init card at 300000 Hz
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
mmc0: mmc_rescan_try_freq: trying to init card at 200000 Hz
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
mmc0: mmc_rescan_try_freq: trying to init card at 100000 Hz
VFS: Mounted root (yaffs2 filesystem) on device 31:2.
devtmpfs: error mounting -2
Freeing init memory: 116K
Failed to execute /linuxrc. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[<c00149bc>] (unwind_backtrace+0x0/0xf8) from [<c0217d84>] (panic+0x90/0x1f8)
[<c0217d84>] (panic+0x90/0x1f8) from [<c021782c>] (kernel_init+0x12c/0x154)
[<c021782c>] (kernel_init+0x12c/0x154) from [<c000f278>] (ret_from_fork+0x14/0x3c