[XILINX] 程序固化实验program flash失败

zc800tc

使用的是领航者v2开发板

boot.bin 放入sd卡可以成功启动，按程序运行，可是使用program flash烧录到qspi时失败，提示如下，请问有哪位兄弟知道原因？



Initialization done
Using default mini u-boot image file - C:/Xilinx/Vitis/2022.2/data\xicom\cfgmem\uboot\zynq_qspi_x4_single.bin
===== mrd->addr=0xF800025C, data=0x00000000 =====
BOOT_MODE REG = 0x00000000
Downloading FSBL...
Running FSBL...
Finished running FSBL.
===== mrd->addr=0xF8000110, data=0x000FA220 =====
READ: ARM_PLL_CFG (0xF8000110) = 0x000FA220
===== mrd->addr=0xF8000100, data=0x00028008 =====
READ: ARM_PLL_CTRL (0xF8000100) = 0x00028008
===== mrd->addr=0xF8000120, data=0x1F000200 =====
READ: ARM_CLK_CTRL (0xF8000120) = 0x1F000200
===== mrd->addr=0xF8000118, data=0x000FA240 =====
READ: IO_PLL_CFG (0xF8000118) = 0x000FA240
===== mrd->addr=0xF8000108, data=0x00036008 =====
READ: IO_PLL_CTRL (0xF8000108) = 0x00036008
Info:  Remapping 256KB of on-chip-memory RAM memory to 0xFFFC0000.
===== mrd->addr=0xF8000008, data=0x00000000 =====
===== mwr->addr=0xF8000008, data=0x0000DF0D =====
MASKWRITE: addr=0xF8000008, mask=0x0000FFFF, newData=0x0000DF0D
===== mwr->addr=0xF8000910, data=0x000001FF =====
===== mrd->addr=0xF8000004, data=0x00000000 =====
===== mwr->addr=0xF8000004, data=0x0000767B =====
MASKWRITE: addr=0xF8000004, mask=0x0000FFFF, newData=0x0000767B




U-Boot 2022.01-00146-g0526f91 (Jul 27 2022 - 03:07:47 -0600)



Model: Zynq CSE QSPI SINGLE Board

DRAM:  256 KiB

WARNING: Caches not enabled

Loading Environment from <NULL>... OK

In:    dcc

Out:   dcc

Err:   dcc

Zynq> sf probe 0 0 0


zynq_qspi_irq_poll: Timeout!

zynq_qspi_irq_poll: Timeout!

jedec_spi_nor flash@0: unrecognized JEDEC id bytes: 90, db, ff

Failed to initialize SPI flash at 0:0 (error -2)

Zynq> ERROR: [Xicom 50-186] Error while detecting SPI flash device - unrecognized JEDEC id bytes: 90, db, ff

Problem in running uboot
Flash programming initialization failed.

ERROR: Flash Operation Failed

caojunye

可以先用网盘里的固化实验的工程在线烧录试试，如果例程工程可以烧录，那么就是flash硬件没有问题。如果是自己的工程不能烧录固化，可能是在创建固化boot.bin文件时对工程的配置哪里设置的不对。按照开发指南文档上的要求，添加文件的顺序以及类型要选对