初级会员
- 积分
- 82
- 金钱
- 82
- 注册时间
- 2018-10-10
- 在线时间
- 11 小时
|
U-Boot 2016.03-g4475ea1 (Apr 29 2020 - 18:34:01 +0800)
CPU: Freescale i.MX6ULL rev1.1 69 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 39C
Reset cause: POR
Board: MX6ULL 14x14 EVK
I2C: ready
DRAM: 512 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
Display: ATK-LCD-4.3-480x272 (480x272)
Video: 480x272x24
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc0 is current device
Net: FEC1
Error: FEC1 address not set.
Normal Boot
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6786368 bytes read in 366 ms (17.7 MiB/s)
Booting from mmc ...
reading imx6ull-14x14-nand-4.3-480x272-c.dtb
39249 bytes read in 19 ms (2 MiB/s)
Kernel image @ 0x80800000 [ 0x000000 - 0x678d40 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300c950
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.15-gb8ddbbc (alientek@ubuntu) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Wed Apr 29 17:39:59 CST 2020
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[ 0.000000] Reserved memory: created CMA memory pool at 0x98000000, size 128 MiB
[ 0.000000] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @97b8f000 s16780 r8192 d24180 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 mtdparts=gpmi-nand:4m(u-boot),128k(env),1m(logo),1m(dtb),8m(kernel),-(rootfs) root=/dev/mmcblk0p2 rootwait rw
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 375276K/524288K available (8547K kernel code, 450K rwdata, 2964K rodata, 524K init, 451K bss, 17940K reserved, 131072K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
[ 0.000000] .text : 0x80008000 - 0x80b46274 (11513 kB)
[ 0.000000] .init : 0x80b47000 - 0x80bca000 ( 524 kB)
[ 0.000000] .data : 0x80bca000 - 0x80c3a9a0 ( 451 kB)
[ 0.000000] .bss : 0x80c3d000 - 0x80cadfc4 ( 452 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mxc_clocksource_init 3000000
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000015] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[ 0.000058] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[ 0.002885] Console: colour dummy device 80x30
[ 0.002924] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.002959] pid_max: default: 32768 minimum: 301
[ 0.003190] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003219] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004610] CPU: Testing write buffer coherency: ok
[ 0.005103] /cpus/cpu@0 missing clock-frequency property
[ 0.005146] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.005255] Setting up static identity map for 0x80008280 - 0x800082d8
[ 0.041190] Brought up 1 CPUs
[ 0.041231] SMP: Total of 1 processors activated (6.00 BogoMIPS).
[ 0.041251] CPU: All CPU(s) started in SVC mode.
[ 0.042355] devtmpfs: initialized
[ 0.059401] device-tree: Duplicate name in lcdif@021c8000, renamed to "display#1"
[ 0.065898] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.066789] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.076875] pinctrl core: initialized pinctrl subsystem
[ 0.079563] NET: Registered protocol family 16
[ 0.097521] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.121344] cpuidle: using governor ladder
[ 0.151404] cpuidle: using governor menu
[ 0.201501] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.201537] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.206084] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.206893] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.279290] mxs-dma 1804000.dma-apbh: initialized
[ 0.286547] SCSI subsystem initialized
[ 0.287904] usbcore: registered new interface driver usbfs
[ 0.288094] usbcore: registered new interface driver hub
[ 0.288315] usbcore: registered new device driver usb
[ 0.291308] i2c i2c-0: IMX I2C adapter registered
[ 0.291356] i2c i2c-0: can't use DMA
[ 0.293380] i2c i2c-1: IMX I2C adapter registered
[ 0.293426] i2c i2c-1: can't use DMA
[ 0.293744] Linux video capture interface: v2.00
[ 0.293953] pps_core: LinuxPPS API ver. 1 registered
[ 0.293978] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.294058] PTP clock support registered
[ 0.297015] MIPI CSI2 driver module loaded
[ 0.297748] Advanced Linux Sound Architecture Driver Initialized.
[ 0.299964] Bluetooth: Core ver 2.20
[ 0.300096] NET: Registered protocol family 31
[ 0.300119] Bluetooth: HCI device and connection manager initialized
[ 0.300162] Bluetooth: HCI socket layer initialized
[ 0.300195] Bluetooth: L2CAP socket layer initialized
[ 0.300279] Bluetooth: SCO socket layer initialized
[ 0.303024] Switched to clocksource mxc_timer1
[ 0.330128] NET: Registered protocol family 2
[ 0.331740] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.331876] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.332035] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.332170] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.332231] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.332655] NET: Registered protocol family 1
[ 0.333505] RPC: Registered named UNIX socket transport module.
[ 0.333539] RPC: Registered udp transport module.
[ 0.333560] RPC: Registered tcp transport module.
[ 0.333579] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.337071] imx rpmsg driver is registered.
[ 0.339940] Bus freq driver module loaded
[ 0.342129] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.359206] VFS: Disk quotas dquot_6.6.0
[ 0.359732] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.365546] NFS: Registering the id_resolver key type
[ 0.365647] Key type id_resolver registered
[ 0.365669] Key type id_legacy registered
[ 0.365863] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.367783] fuse init (API version 7.23)
[ 0.378943] io scheduler noop registered
[ 0.378996] io scheduler deadline registered
[ 0.379506] io scheduler cfq registered (default)
[ 0.380667] imx-weim 21b8000.weim: Driver registered.
[ 0.387607] backlight supply power not found, using dummy regulator
[ 0.390111] MIPI DSI driver module loaded
[ 0.390616] MIPI DSI driver module loaded
[ 0.396850] 21c8000.lcdif supply lcd not found, using dummy regulator
[ 0.504707] mxsfb 21c8000.lcdif: failed to find mxc display driver
[ 0.510029] Console: switching to colour frame buffer device 60x34
[ 0.530751] mxsfb 21c8000.lcdif: initialized
[ 0.532953] imx-sdma 20ec000.sdma: no event needs to be remapped
[ 0.533284] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 0.540645] imx-sdma 20ec000.sdma: initialized
[ 0.542929] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.238354] console [ttymxc0] enabled
[ 1.244103] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 232, base_baud = 5000000) is a IMX
[ 1.342246] imx-rng 2284000.rngb: iMX RNG Registered.
[ 1.348113] imx sema4 driver is registered.
[ 1.352509] [drm] Initialized drm 1.1.0 20060810
[ 1.358568] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 1.390915] brd: module loaded
[ 1.407421] loop: module loaded
[ 1.427299] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
[ 1.433761] nand: Micron MT29F4G08ABADAWP
[ 1.437812] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.446279] gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 5
[ 1.453741] Bad block table found at page 262080, version 0x01
[ 1.459821] Bad block table found at page 262016, version 0x01
[ 1.466228] 6 cmdlinepart partitions found on MTD device gpmi-nand
[ 1.472448] Creating 6 MTD partitions on "gpmi-nand":
[ 1.477606] 0x000000000000-0x000000400000 : "u-boot"
[ 1.485350] 0x000000400000-0x000000420000 : "env"
[ 1.492597] 0x000000420000-0x000000520000 : "logo"
[ 1.500077] 0x000000520000-0x000000620000 : "dtb"
[ 1.507320] 0x000000620000-0x000000e20000 : "kernel"
[ 1.514939] 0x000000e20000-0x000020000000 : "rootfs"
[ 1.524050] gpmi-nand 1806000.gpmi-nand: driver registered.
[ 1.533593] spi_imx 2010000.ecspi: probed
[ 1.540384] CAN device driver interface
[ 1.547519] flexcan 2090000.can: device registered (reg_base=a0a28000, irq=27)
[ 1.557265] 20b4000.ethernet supply phy not found, using dummy regulator
[ 1.774238] pps pps0: new PPS source ptp0
[ 1.779780] fec 20b4000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 1.789920] fec 20b4000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 12:61:75:b7:c6:97
[ 1.801308] libphy: fec_enet_mii_bus: probed
[ 1.809902] fec 20b4000.ethernet eth0: registered PHC device 0
[ 1.817757] 2188000.ethernet supply phy not found, using dummy regulator
[ 2.034207] pps pps1: new PPS source ptp1
[ 2.039740] fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 2.049979] fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: e6:3d:3b:0f:ba:bd
[ 2.062753] fec 2188000.ethernet eth1: registered PHC device 1
[ 2.070524] PPP generic driver version 2.4.2
[ 2.075529] PPP BSD Compression module registered
[ 2.080295] PPP Deflate Compression module registered
[ 2.085503] PPP MPPE Compression module registered
[ 2.090360] NET: Registered protocol family 24
[ 2.095186] usbcore: registered new interface driver asix
[ 2.100801] usbcore: registered new interface driver ax88179_178a
[ 2.107171] usbcore: registered new interface driver cdc_ether
[ 2.113260] usbcore: registered new interface driver net1080
[ 2.119134] usbcore: registered new interface driver cdc_subset
[ 2.125398] usbcore: registered new interface driver zaurus
[ 2.131279] usbcore: registered new interface driver cdc_ncm
[ 2.137063] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.143690] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.149574] usbcore: registered new interface driver usb-storage
[ 2.155877] usbcore: registered new interface driver usb_ehset_test
[ 2.165194] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 2.174584] 2184000.usb supply vbus not found, using dummy regulator
[ 2.186685] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 2.191647] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[ 2.213168] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 2.220825] hub 1-0:1.0: USB hub found
[ 2.224885] hub 1-0:1.0: 1 port detected
[ 2.230726] 2184200.usb supply vbus not found, using dummy regulator
[ 2.241244] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 2.246384] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[ 2.273164] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 2.280840] hub 2-0:1.0: USB hub found
[ 2.284909] hub 2-0:1.0: 1 port detected
[ 2.291487] mousedev: PS/2 mouse device common for all mice
[ 2.299249] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[ 2.313795] <<-GTP-INFO->> GTP driver installing...
[ 2.319441] <<-GTP-INFO->> GTP Driver Version: V2.4<2014/11/28>
[ 2.326771] <<-GTP-INFO->> GTP I2C Address: 0x5d
[ 2.331487] 1-005d supply vdd_ana not found, using dummy regulator
[ 2.337947] 1-005d supply vcc_i2c not found, using dummy regulator
[ 2.344333] <<-GTP-INFO->> Guitar reset
[ 2.474124] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 2.482333] <<-GTP-INFO->> Guitar reset
[ 2.603109] usb 2-1: new high-speed USB device number 2 using ci_hdrc
[ 2.609673] <<-GTP-ERROR->> GTP i2c test failed time 1.
[ 2.634165] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 2.642394] <<-GTP-INFO->> Guitar reset
[ 2.763116] <<-GTP-ERROR->> GTP i2c test failed time 2.
[ 2.771915] hub 2-1:1.0: USB hub found
[ 2.776274] hub 2-1:1.0: 4 ports detected
[ 2.784170] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 2.792417] <<-GTP-INFO->> Guitar reset
[ 2.913069] <<-GTP-ERROR->> GTP i2c test failed time 3.
[ 2.934166] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 2.942375] <<-GTP-INFO->> Guitar reset
[ 3.063062] <<-GTP-ERROR->> GTP i2c test failed time 4.
[ 3.084174] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.092381] <<-GTP-INFO->> Guitar reset
[ 3.213054] <<-GTP-ERROR->> GTP i2c test failed time 5.
[ 3.233057] <<-GTP-ERROR->> I2C communication ERROR!
[ 3.238101] goodix-ts: probe of 1-005d failed with error -5
[ 3.247988] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
[ 3.257183] i2c /dev entries driver
[ 3.263655] IR NEC protocol handler initialized
[ 3.268242] IR RC5(x/sz) protocol handler initialized
[ 3.273389] IR RC6 protocol handler initialized
[ 3.277957] IR JVC protocol handler initialized
[ 3.282521] IR Sony protocol handler initialized
[ 3.287218] IR SANYO protocol handler initialized
[ 3.291960] IR Sharp protocol handler initialized
[ 3.296743] IR MCE Keyboard/mouse protocol handler initialized
[ 3.302615] IR XMP protocol handler initialized
[ 3.310637] pxp-v4l2 pxp_v4l2: initialized
[ 3.316891] 0-000e supply vdd not found, using dummy regulator
[ 3.322897] 0-000e supply vddio not found, using dummy regulator
[ 3.329275] mag3110 0-000e: check mag3110 chip ID
[ 3.334373] mag3110 0-000e: read chip ID 0xfffffffb is not equal to 0xc4!
[ 3.341437] mag3110: probe of 0-000e failed with error -22
[ 3.349488] imx2-wdt 20bc000.wdog: use WDOG_B to reboot.
[ 3.355985] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 3.362231] Bluetooth: HCI UART driver ver 2.3
[ 3.366944] Bluetooth: HCI UART protocol H4 registered
[ 3.372120] Bluetooth: HCI UART protocol BCSP registered
[ 3.377523] Bluetooth: HCI UART protocol ATH3K registered
[ 3.383296] usbcore: registered new interface driver bcm203x
[ 3.389233] usbcore: registered new interface driver btusb
[ 3.395063] usbcore: registered new interface driver ath3k
[ 3.401689] sdhci: Secure Digital Host Controller Interface driver
[ 3.408002] sdhci: Copyright(c) Pierre Ossman
[ 3.412410] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.420736] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
[ 3.428079] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[ 3.434459] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
[ 3.484572] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 3.524559] usbcore: registered new interface driver usbhid
[ 3.530180] usbhid: USB HID core driver
[ 3.555167] fsl-asrc 2034000.asrc: driver registered
[ 3.566363] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.581746] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 3.594086] imx-wm8960 sound: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[ 3.601382] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 3.609073] mmc0: new high speed SDHC card at address 59b4
[ 3.616749] mmcblk0: mmc0:59b4 USD00 7.32 GiB
[ 3.625226] mmcblk0: p1 p2
[ 3.741015] NET: Registered protocol family 26
[ 3.747707] NET: Registered protocol family 10
[ 3.755029] sit: IPv6 over IPv4 tunneling driver
[ 3.761626] NET: Registered protocol family 17
[ 3.766383] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 3.779183] can: controller area network core (rev 20120528 abi 9)
[ 3.785634] NET: Registered protocol family 29
[ 3.790177] can: raw protocol (rev 20120528)
[ 3.794563] can: broadcast manager protocol (rev 20120528 t)
[ 3.800292] can: netlink gateway (rev 20130117) max_hops=1
[ 3.806550] Bluetooth: RFCOMM TTY layer initialized
[ 3.811501] Bluetooth: RFCOMM socket layer initialized
[ 3.816957] Bluetooth: RFCOMM ver 1.11
[ 3.820791] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.826202] Bluetooth: BNEP filters: protocol multicast
[ 3.831483] Bluetooth: BNEP socket layer initialized
[ 3.836543] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.842513] Bluetooth: HIDP socket layer initialized
[ 3.847694] 8021q: 802.1Q VLAN Support v1.8
[ 3.852062] Key type dns_resolver registered
[ 3.881887] dhd_module_init in
[ 3.886510] input: gpio_keys@0 as /devices/platform/gpio_keys@0/input/input1
[ 3.894346] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 2019-08-14 12:45:12 UTC (1565786712)
[ 3.918420] gpio_dvfs: disabling
[ 3.921691] can-3v3: disabling
[ 3.925186] ALSA device list:
[ 3.928179] #0: wm8960-audio
[ 3.940698] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[ 3.951033] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244)
[ 4.283299] random: nonblocking pool is initialized
[ 6.670398] EXT4-fs (mmcblk0p2): recovery complete
[ 6.717133] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 6.725429] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 6.734953] devtmpfs: mounted
[ 6.738788] Freeing unused kernel memory: 524K (80b47000 - 80bca000)
INIT: version 2.88 booting
Starting udev
[ 7.745828] udevd[130]: starting version 3.1.5
[ 8.262227] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 8.501817] 1-003c supply DOVDD not found, using dummy regulator
[ 8.538066] 1-003c supply DVDD not found, using dummy regulator
[ 8.583972] 1-003c supply AVDD not found, using dummy regulator
bootlogd: cannot allocate pseudo tty: No such file or directory
[ 8.723415] ov5640_read_reg:write reg error:reg=300a
[ 8.746688] camera ov5640 is not found
[ 9.833187] usb 2-1.2: new high-speed USB device number 3 using ci_hdrc
[ 10.124534] cdc_ether 2-1.2:1.3 usb0: register 'cdc_ether' at usb-ci_hdrc.1-1.2, CDC Ethernet Device, 36:90:1e:30:3b:45
[ 11.137025] usbcore: registered new interface driver usbserial
[ 11.314416] usbcore: registered new interface driver usbserial_generic
[ 11.365480] usbserial: USB Serial support registered for generic
[ 11.423634] usbcore: registered new interface driver option
[ 11.447432] usbserial: USB Serial support registered for GSM modem (1-port)
[ 11.466610] idVendor=19d2, idProduct=1476, bInterfaceNumber =0
[ 11.480100] option 2-1.2:1.0: GSM modem (1-port) converter detected
[ 11.498890] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 11.515779] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB0
[ 11.541843] idVendor=19d2, idProduct=1476, bInterfaceNumber =1
[ 11.582633] option 2-1.2:1.1: GSM modem (1-port) converter detected
[ 11.594810] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB1
[ 11.612438] idVendor=19d2, idProduct=1476, bInterfaceNumber =2
[ 11.629057] option 2-1.2:1.2: GSM modem (1-port) converter detected
[ 11.649534] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB2
ALSA: Restoring mixer settings...
Found hardware: "wm8960-audio" "" "" "" ""
Hardware is initialized using a generic method
/usr/sbin/alsactl: set_control:1325: failed to obtain info for control #58 (No such file or directory)
INIT: Entering runlevel: 5
Configuring network interfaces... [ 12.693728] fec 20b4000.ethernet eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet:01, irq=-1)
[ 12.733143] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
done.
Starting system message bus: Starting Xserver
dbus.
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting rpcbind daemon...done.
starting statd: [ 13.983661] fec 2188000.ethernet eth1: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=20b4000.ethernet:00, irq=-1)
[ 14.023176] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
done
Starting advanced power management daemon: [ 14.124307] cdc_ether 2-1.2:1.3 usb0: kevent 12 may have been dropped
[ 14.130840] cdc_ether 2-1.2:1.3 usb0: kevent 12 may have been dropped
[ 14.145068] cdc_ether 2-1.2:1.3 usb0: kevent 12 may have been dropped
No APM support in kernel
(failed.)
Starting atd: OK
exportfs: can't open /etc/exports for reading
NFS daemon support not enabled in kernel
Starting system log daemon...0
Starting kernel log daemon...0
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ 15.088977] cdc_ether 2-1.2:1.3 usb0: kevent 12 may have been dropped
[ 15.100528] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ ok ]
Starting Telephony daemon
Starting Linux NFC daemon
Starting crond: OK
Running local boot scripts (/etc/rc.local).
root@ATK-IMX6U:~# [ 17.028409] Unable to handle kernel paging request at virtual address ff020236
[ 17.035663] pgd = 94db8000
[ 17.038378] [ff020236] *pgd=00000000
[ 17.041981] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 17.047300] Modules linked in: option usb_wwan usbserial mx6s_capture ov5640_camera
[ 17.055058] CPU: 0 PID: 638 Comm: QDesktop Not tainted 4.1.15-gb8ddbbc #1
[ 17.061850] Hardware name: Freescale i.MX6 Ultralite (Device Tree)
[ 17.068036] task: 94266140 ti: 947b4000 task.ti: 947b4000
[ 17.073449] PC is at rw_verify_area+0x98/0xf8
[ 17.077813] LR is at vfs_write+0x60/0x16c
[ 17.081831] pc : [<800ebbd4>] lr : [<800ebd9c>] psr: a00f0013
[ 17.081831] sp : 947b5f38 ip : 9200dd20 fp : 52b5d86d
[ 17.093315] r10: 00000000 r9 : 947b4000 r8 : 8000f604
[ 17.098545] r7 : 00000000 r6 : 00000008 r5 : 00000000 r4 : 00000000
[ 17.105078] r3 : 00000008 r2 : ff020202 r1 : 945d5900 r0 : 00000001
[ 17.111612] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 17.118753] Control: 10c53c7d Table: 94db806a DAC: 00000015
[ 17.124506] Process QDesktop (pid: 638, stack limit = 0x947b4210)
[ 17.130604] Stack: (0x947b5f38 to 0x947b6000)
[ 17.134971] 5f20: 948141b8 802d2714
[ 17.143159] 5f40: 00000000 94872c40 a2abfdac 945d5900 945d5900 7e8445e8 947b5f88 8000f604
[ 17.151345] 5f60: 947b4000 800ebd9c 7e844098 00000107 945d5900 945d5900 7e8445e8 00000008
[ 17.159532] 5f80: 8000f604 800ec5e4 00000000 00000000 7e844068 7e8445e8 01279718 012b0338
[ 17.167720] 5fa0: 00000004 8000f480 7e8445e8 01279718 00000003 7e8445e8 00000008 00000000
[ 17.175907] 5fc0: 7e8445e8 01279718 012b0338 00000004 012af850 01280c64 00000000 52b5d86d
[ 17.184095] 5fe0: 00000000 7e8445e4 75a1e768 75c205c0 600f0010 00000003 00000000 00000000
[ 17.192296] [<800ebbd4>] (rw_verify_area) from [<800ebd9c>] (vfs_write+0x60/0x16c)
[ 17.199877] [<800ebd9c>] (vfs_write) from [<800ec5e4>] (SyS_write+0x44/0x9c)
[ 17.206940] [<800ec5e4>] (SyS_write) from [<8000f480>] (ret_fast_syscall+0x0/0x3c)
[ 17.214521] Code: baffffea e3e0004a eafffff0 e59c201c (e5922034)
[ 17.220625] ---[ end trace 0ec9e68623bf3b65 ]---
[ 17.230064] Unable to handle kernel paging request at virtual address ff02020e
[ 17.237310] pgd = 94db8000
[ 17.240023] [ff02020e] *pgd=00000000
[ 17.243622] Internal error: Oops: 5 [#2] PREEMPT SMP ARM
[ 17.248941] Modules linked in: option usb_wwan usbserial mx6s_capture ov5640_camera
[ 17.256696] CPU: 0 PID: 638 Comm: QDesktop Tainted: G D 4.1.15-gb8ddbbc #1
[ 17.264703] Hardware name: Freescale i.MX6 Ultralite (Device Tree)
[ 17.270889] task: 94266140 ti: 947b4000 task.ti: 947b4000
[ 17.276306] PC is at locks_remove_posix+0x10/0x24
[ 17.281023] LR is at filp_close+0x58/0x7c
[ 17.285044] pc : [<8012d8c8>] lr : [<800e9f88>] psr: a00f0113
[ 17.285044] sp : 947b5d50 ip : 00000000 fp : 80a11c74
[ 17.296528] r10: 800ebbd6 r9 : 94801780 r8 : 00000000
[ 17.301758] r7 : 94545900 r6 : 94545900 r5 : 945d5900 r4 : 00000000
[ 17.308292] r3 : ff020202 r2 : 9200dd20 r1 : 94545900 r0 : 945d5900
[ 17.314827] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 17.321969] Control: 10c53c7d Table: 94db806a DAC: 00000015
[ 17.327719] Process QDesktop (pid: 638, stack limit = 0x947b4210)
[ 17.333817] Stack: (0x947b5d50 to 0x947b6000)
[ 17.338184] 5d40: 000003ff 0000000c 00000000 801059f0
[ 17.346373] 5d60: 94266140 94872c40 94872c78 00000000 94266548 00000001 800ebbd6 80037f78
[ 17.354561] 5d80: 80bd0be4 600f0193 0000000b 800ebbd8 00000001 0000000b 80a11c74 8001294c
[ 17.362749] 5da0: 947b4210 0000000b 00000000 7f000000 00000008 80a11c7c 62000000 66666661
[ 17.370937] 5dc0: 20616566 30653365 61343030 66616520 66666666 35652030 30326339 28206331
[ 17.379124] 5de0: 32393565 34333032 80002029 947b5e0c 52b5d86d ff020236 947b5ef0 00000005
[ 17.387312] 5e00: 94872c40 947b5ef0 947b4000 00000000 52b5d86d 80821060 94872c40 8001c4c0
[ 17.395500] 5e20: 9456f4bc 97bf8020 80c3a604 000007f8 80007fc0 80004000 ff020236 8001c53c
[ 17.403688] 5e40: 80bd0e94 00000005 8001c4d0 80009288 97e95d00 00000001 00080000 800b3238
[ 17.411875] 5e60: 947b5eb4 00000000 97e95d00 80c397c0 00000000 97e95d00 00000002 800b4fe0
[ 17.420062] 5e80: 80c8a4e0 948141ec 94637cf0 947b5eb4 947b5ec8 00000000 00000000 00000000
[ 17.428250] 5ea0: 97e46420 00000001 00080000 800b3238 00000000 00000000 97e46420 80c397c0
[ 17.436438] 5ec0: 00000000 97e46420 00000000 800b4fe0 948141b8 00000000 800ebbd4 a00f0013
[ 17.444626] 5ee0: ffffffff 947b5f24 8000f604 80013198 00000001 945d5900 ff020202 00000008
[ 17.452813] 5f00: 00000000 00000000 00000008 00000000 8000f604 947b4000 00000000 52b5d86d
[ 17.461001] 5f20: 9200dd20 947b5f38 800ebd9c 800ebbd4 a00f0013 ffffffff 948141b8 802d2714
[ 17.469188] 5f40: 00000000 94872c40 a2abfdac 945d5900 945d5900 7e8445e8 947b5f88 8000f604
[ 17.477377] 5f60: 947b4000 800ebd9c 7e844098 00000107 945d5900 945d5900 7e8445e8 00000008
[ 17.485564] 5f80: 8000f604 800ec5e4 00000000 00000000 7e844068 7e8445e8 01279718 012b0338
[ 17.493752] 5fa0: 00000004 8000f480 7e8445e8 01279718 00000003 7e8445e8 00000008 00000000
[ 17.501940] 5fc0: 7e8445e8 01279718 012b0338 00000004 012af850 01280c64 00000000 52b5d86d
[ 17.510129] 5fe0: 00000000 7e8445e4 75a1e768 75c205c0 600f0010 00000003 00000000 00000000
[ 17.518331] [<8012d8c8>] (locks_remove_posix) from [<800e9f88>] (filp_close+0x58/0x7c)
[ 17.526265] [<800e9f88>] (filp_close) from [<801059f0>] (put_files_struct+0xa4/0xfc)
[ 17.534022] [<801059f0>] (put_files_struct) from [<80037f78>] (do_exit+0x2c8/0x9ac)
[ 17.541697] [<80037f78>] (do_exit) from [<8001294c>] (die+0x22c/0x3fc)
[ 17.548246] [<8001294c>] (die) from [<80821060>] (__do_kernel_fault.part.0+0x64/0x74)
[ 17.556091] [<80821060>] (__do_kernel_fault.part.0) from [<8001c4c0>] (do_sect_fault+0x0/0x10)
[ 17.564715] [<8001c4c0>] (do_sect_fault) from [<97bf8020>] (0x97bf8020)
[ 17.571342] Code: e5903010 e59330d0 e3530000 012fff1e (e593200c)
[ 17.577444] ---[ end trace 0ec9e68623bf3b66 ]---
[ 17.582068] Fixing recursive fault but reboot is needed!
|
|
/2 
|手机版|OpenEdv-开源电子网
( 粤ICP备12000418号-1 )
发表于 2020-11-6 11:24:53
楼主
