使用 mfgtool 上位机固化系统（OTG 方式），重启后，卡在进度页面不动，请各位大神指点迷津。谢谢

changming411 · 发表于 2020-6-15 22:46:08

串口打印数据如下：
U-Boot 2016.03-g9bd38ef (Oct 23 2019 - 09:31:57 +0800)
CPU: Freescale i.MX6ULL rev1.1 69 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 51C
Reset cause: POR
Board: MX6ULL 14x14 EVK
I2C: ready
DRAM:  512 MiB
NAND:  512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
Display: ATK-LCD-7-1024x600 (1024x600)
Video: 1024x600x24
NAND read: device 0 offset 0x420000, size 0x100000
1048576 bytes read: OK
Error: no valid bmp image at 88000000
In: serial
Out: serial
Err: serial
Net: FEC1
Error: FEC1 address not set.
Normal Boot
Hit any key to stop autoboot:  0
NAND read: device 0 offset 0x620000, size 0x800000
8388608 bytes read: OK
NAND read: device 0 offset 0x580000, size 0x20000
131072 bytes read: OK
Kernel image @ 0x80800000 [ 0x000000 - 0x676908 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300c727
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.15-g49efdaa (alientek@ubuntu) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Mon Oct 14 12:41:57 CST 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[ 0.000000] Reserved memory: created CMA memory pool at 0x98000000, size 128 MiB
[ 0.000000] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @97b90000 s16780 r8192 d24180 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 ubi.mtd=5 root=ubi0:rootfs rootfstype=ubifs mtdparts=gpmi-nand:4m(u-boot),128k(env),1m(logo),1m(dtb),8m(kernel),-(rootfs)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 375368K/524288K available (8547K kernel code, 449K rwdata, 2964K rodata, 436K init, 451K bss, 17848K reserved, 131072K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000]    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000]    fixmap  : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000]    vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
[ 0.000000]    lowmem  : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000]    pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000]    modules : 0x7f000000 - 0x7fe00000 (  14 MB)
[ 0.000000]    .text : 0x80008000 - 0x80b4624c (11513 kB)
[ 0.000000]    .init : 0x80b47000 - 0x80bb4000 ( 436 kB)
[ 0.000000]    .data : 0x80bb4000 - 0x80c24620 ( 450 kB)
[ 0.000000]       .bss : 0x80c27000 - 0x80c97fc4 ( 452 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000]  Additional per-CPU info printed with stalls.
[ 0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mxc_clocksource_init 3000000
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000016] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[ 0.000057] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[ 0.002843] Console: colour dummy device 80x30
[ 0.002885] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.002919] pid_max: default: 32768 minimum: 301
[ 0.003148] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003177] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004577] CPU: Testing write buffer coherency: ok
[ 0.005065] /cpus/cpu@0 missing clock-frequency property
[ 0.005106] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.005218] Setting up static identity map for 0x80008280 - 0x800082d8
[ 0.041183] Brought up 1 CPUs
[ 0.041222] SMP: Total of 1 processors activated (6.00 BogoMIPS).
[ 0.041242] CPU: All CPU(s) started in SVC mode.
[ 0.042361] devtmpfs: initialized
[ 0.059217] device-tree: Duplicate name in lcdif@021c8000, renamed to "display#1"
[ 0.065580] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.066482] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.076566] pinctrl core: initialized pinctrl subsystem
[ 0.079268] NET: Registered protocol family 16
[ 0.097310] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.121055] cpuidle: using governor ladder
[ 0.151120] cpuidle: using governor menu
[ 0.200788] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.200824] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.205379] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.206172] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[ 0.278895] mxs-dma 1804000.dma-apbh: initialized
[ 0.286165] SCSI subsystem initialized
[ 0.287545] usbcore: registered new interface driver usbfs
[ 0.287735] usbcore: registered new interface driver hub
[ 0.287955] usbcore: registered new device driver usb
[ 0.290921] i2c i2c-0: IMX I2C adapter registered
[ 0.290969] i2c i2c-0: can't use DMA
[ 0.292979] i2c i2c-1: IMX I2C adapter registered
[ 0.293026] i2c i2c-1: can't use DMA
[ 0.293349] Linux video capture interface: v2.00
[ 0.293557] pps_core: LinuxPPS API ver. 1 registered
[ 0.293582] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.293656] PTP clock support registered
[ 0.296671] MIPI CSI2 driver module loaded
[ 0.297349] Advanced Linux Sound Architecture Driver Initialized.
[ 0.299584] Bluetooth: Core ver 2.20
[ 0.299716] NET: Registered protocol family 31
[ 0.299738] Bluetooth: HCI device and connection manager initialized
[ 0.299779] Bluetooth: HCI socket layer initialized
[ 0.299815] Bluetooth: L2CAP socket layer initialized
[ 0.299900] Bluetooth: SCO socket layer initialized
[ 0.302585] Switched to clocksource mxc_timer1
[ 0.329943] NET: Registered protocol family 2
[ 0.331542] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.331677] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.331836] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.331976] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.332040] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.332477] NET: Registered protocol family 1
[ 0.333332] RPC: Registered named UNIX socket transport module.
[ 0.333366] RPC: Registered udp transport module.
[ 0.333388] RPC: Registered tcp transport module.
[ 0.333408] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.336899] imx rpmsg driver is registered.
[ 0.339758] Bus freq driver module loaded
[ 0.341978] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.359221] VFS: Disk quotas dquot_6.6.0
[ 0.359734] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.365512] NFS: Registering the id_resolver key type
[ 0.365639] Key type id_resolver registered
[ 0.365661] Key type id_legacy registered
[ 0.365855] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.367792] fuse init (API version 7.23)
[ 0.379139] io scheduler noop registered
[ 0.379191] io scheduler deadline registered
[ 0.379679] io scheduler cfq registered (default)
[ 0.380833] imx-weim 21b8000.weim: Driver registered.
[ 0.387867] backlight supply power not found, using dummy regulator
[ 0.390363] MIPI DSI driver module loaded
[ 0.390876] MIPI DSI driver module loaded
[ 0.397089] 21c8000.lcdif supply lcd not found, using dummy regulator
[ 0.505043] mxsfb 21c8000.lcdif: failed to find mxc display driver
[ 0.520189] Console: switching to colour frame buffer device 128x37
[ 0.536862] mxsfb 21c8000.lcdif: initialized
[ 0.539042] imx-sdma 20ec000.sdma: no event needs to be remapped
[ 0.539257] imx-sdma 20ec000.sdma: loaded firmware 3.3
[ 0.546617] imx-sdma 20ec000.sdma: initialized
[ 0.548861] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX
[ 1.245160] console [ttymxc0] enabled
[ 1.250752] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 232, base_baud = 5000000) is a IMX
[ 1.348830] imx-rng 2284000.rngb: iMX RNG Registered.
[ 1.354696] imx sema4 driver is registered.
[ 1.359082] [drm] Initialized drm 1.1.0 20060810
[ 1.365133] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 1.397111] brd: module loaded
[ 1.413435] loop: module loaded
[ 1.433069] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
[ 1.439475] nand: Micron MT29F4G08ABADAWP
[ 1.443576] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.451985] gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 5
[ 1.459492] Bad block table found at page 262080, version 0x01
[ 1.465630] Bad block table found at page 262016, version 0x01
[ 1.471935] 6 cmdlinepart partitions found on MTD device gpmi-nand
[ 1.478222] Creating 6 MTD partitions on "gpmi-nand":
[ 1.483358] 0x000000000000-0x000000400000 : "u-boot"
[ 1.490962] 0x000000400000-0x000000420000 : "env"
[ 1.498298] 0x000000420000-0x000000520000 : "logo"
[ 1.505794] 0x000000520000-0x000000620000 : "dtb"
[ 1.513069] 0x000000620000-0x000000e20000 : "kernel"
[ 1.520424] 0x000000e20000-0x000020000000 : "rootfs"
[ 1.529418] gpmi-nand 1806000.gpmi-nand: driver registered.
[ 1.538895] spi_imx 2010000.ecspi: probed
[ 1.545428] CAN device driver interface
[ 1.552261] flexcan 2090000.can: device registered (reg_base=a0a28000, irq=27)
[ 1.561939] 20b4000.ethernet supply phy not found, using dummy regulator
[ 1.603792] pps pps0: new PPS source ptp0
[ 1.609350] fec 20b4000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 1.619490] fec 20b4000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: a2:46:cf:e7:47:45
[ 1.630854] libphy: fec_enet_mii_bus: probed
[ 1.639239] fec 20b4000.ethernet eth0: registered PHC device 0
[ 1.647035] 2188000.ethernet supply phy not found, using dummy regulator
[ 1.693755] pps pps1: new PPS source ptp1
[ 1.699361] fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 1.709502] fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 36:26:f3:5e:7c:f3
[ 1.722185] fec 2188000.ethernet eth1: registered PHC device 1
[ 1.729927] PPP generic driver version 2.4.2
[ 1.734990] PPP BSD Compression module registered
[ 1.739752] PPP Deflate Compression module registered
[ 1.744962] PPP MPPE Compression module registered
[ 1.749815] NET: Registered protocol family 24
[ 1.754640] usbcore: registered new interface driver asix
[ 1.760251] usbcore: registered new interface driver ax88179_178a
[ 1.766607] usbcore: registered new interface driver cdc_ether
[ 1.772695] usbcore: registered new interface driver net1080
[ 1.778587] usbcore: registered new interface driver cdc_subset
[ 1.784767] usbcore: registered new interface driver zaurus
[ 1.790643] usbcore: registered new interface driver cdc_ncm
[ 1.796416] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.803032] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.808893] usbcore: registered new interface driver usb-storage
[ 1.815186] usbcore: registered new interface driver usb_ehset_test
[ 1.824438] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 1.833763] 2184000.usb supply vbus not found, using dummy regulator
[ 1.846928] 2184200.usb supply vbus not found, using dummy regulator
[ 1.857423] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 1.862411] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 1.882721] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 1.890302] hub 1-0:1.0: USB hub found
[ 1.894385] hub 1-0:1.0: 1 port detected
[ 1.900912] mousedev: PS/2 mouse device common for all mice
[ 1.908642] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[ 2.212656] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 2.262137] input: EP0820M09 as /devices/platform/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0038/input/input1
[ 2.274230] <<-GTP-INFO->> GTP driver installing...
[ 2.283764] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
[ 2.292967] i2c /dev entries driver
[ 2.299340] IR NEC protocol handler initialized
[ 2.304028] IR RC5(x/sz) protocol handler initialized
[ 2.309122] IR RC6 protocol handler initialized
[ 2.313733] IR JVC protocol handler initialized
[ 2.318299] IR Sony protocol handler initialized
[ 2.322998] IR SANYO protocol handler initialized
[ 2.327738] IR Sharp protocol handler initialized
[ 2.332475] IR MCE Keyboard/mouse protocol handler initialized
[ 2.338566] IR XMP protocol handler initialized
[ 2.346582] pxp-v4l2 pxp_v4l2: initialized
[ 2.352943] 0-000e supply vdd not found, using dummy regulator
[ 2.358974] 0-000e supply vddio not found, using dummy regulator
[ 2.365212] mag3110 0-000e: check mag3110 chip ID
[ 2.370223] mag3110 0-000e: read chip ID 0xfffffffb is not equal to 0xc4!
[ 2.377445] mag3110: probe of 0-000e failed with error -22
[ 2.386584] hub 1-1:1.0: USB hub found
[ 2.391959] imx2-wdt 20bc000.wdog: use WDOG_B to reboot.
[ 2.397567] hub 1-1:1.0: 4 ports detected
[ 2.404127] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 2.410640] Bluetooth: HCI UART driver ver 2.3
[ 2.415999] Bluetooth: HCI UART protocol H4 registered
[ 2.421219] Bluetooth: HCI UART protocol BCSP registered
[ 2.426615] Bluetooth: HCI UART protocol ATH3K registered
[ 2.432376] usbcore: registered new interface driver bcm203x
[ 2.438351] usbcore: registered new interface driver btusb
[ 2.444159] usbcore: registered new interface driver ath3k
[ 2.450795] sdhci: Secure Digital Host Controller Interface driver
[ 2.457109] sdhci: Copyright(c) Pierre Ossman
[ 2.461513] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.469767] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
[ 2.477106] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[ 2.484463] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
[ 2.535416] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 2.555445] usbcore: registered new interface driver usbhid
[ 2.561065] usbhid: USB HID core driver
[ 2.579612] fsl-asrc 2034000.asrc: driver registered
[ 2.596747] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 2.605799] imx-wm8960 sound: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[ 2.613329] imx-wm8960 sound: wm8960-hifi <-> 202c000.sai mapping ok
[ 2.740224] NET: Registered protocol family 26
[ 2.746791] NET: Registered protocol family 10
[ 2.754055] sit: IPv6 over IPv4 tunneling driver
[ 2.760619] NET: Registered protocol family 17
[ 2.765402] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.778131] can: controller area network core (rev 20120528 abi 9)
[ 2.784583] NET: Registered protocol family 29
[ 2.789117] can: raw protocol (rev 20120528)
[ 2.793500] can: broadcast manager protocol (rev 20120528 t)
[ 2.799226] can: netlink gateway (rev 20130117) max_hops=1
[ 2.805463] Bluetooth: RFCOMM TTY layer initialized
[ 2.810414] Bluetooth: RFCOMM socket layer initialized
[ 2.815821] Bluetooth: RFCOMM ver 1.11
[ 2.819650] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.825052] Bluetooth: BNEP filters: protocol multicast
[ 2.830331] Bluetooth: BNEP socket layer initialized
[ 2.835384] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.841347] Bluetooth: HIDP socket layer initialized
[ 2.846509] 8021q: 802.1Q VLAN Support v1.8
[ 2.850863] Key type dns_resolver registered
[ 2.881332] ubi0: attaching mtd5
[ 3.130734] random: nonblocking pool is initialized
[ 3.937686] ubi0: scanning is finished
[ 3.954399] ubi0: attached mtd5 (name "rootfs", size 497 MiB)
[ 3.960181] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.967165] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.974000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.980973] ubi0: good PEBs: 3979, bad PEBs: 4, corrupted PEBs: 0
[ 3.987108] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 3.994437] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1047211440
[ 4.003614] ubi0: available PEBs: 0, total reserved PEBs: 3979, PEBs reserved for bad PEB handling: 76
[ 4.012967] ubi0: background thread "ubi_bgt0d" started, PID 86
[ 4.018937] dhd_module_init in
[ 4.023515] input: gpio_keys@0 as /devices/platform/gpio_keys@0/input/input2
[ 4.031202] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 2019-08-14 16:07:37 UTC (1565798857)
[ 4.054796] gpio_dvfs: disabling
[ 4.058066] VSD_3V3: disabling
[ 4.061131] can-3v3: disabling
[ 4.064544] ALSA device list:
[ 4.067531] #0: wm8960-audio
[ 4.089033] UBIFS (ubi0:0): recovery needed
[ 4.109916] UBIFS (ubi0:0): recovery deferred
[ 4.114502] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[ 4.122823] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 4.132832] UBIFS (ubi0:0): FS size: 493047808 bytes (470 MiB, 3883 LEBs), journal size 24633344 bytes (23 MiB, 194 LEBs)
[ 4.143828] UBIFS (ubi0:0): reserved for root: 4952683 bytes (4836 KiB)
[ 4.150459] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID D1A66FA8-AD3D-4C8E-9875-8EA7D71BF3C1, small LPT model
[ 4.162939] VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
[ 4.170443] devtmpfs: mounted
[ 4.174058] Freeing unused kernel memory: 436K (80b47000 - 80bb4000)
INIT: version 2.88 booting
Starting udev
[ 5.288988] udevd[127]: starting version 3.1.5
[ 5.740056] UBIFS (ubi0:0): completing deferred recovery
[ 5.846980] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 161
[ 5.857469] UBIFS (ubi0:0): deferred recovery completed
[ 6.066126] 1-003c supply DOVDD not found, using dummy regulator
[ 6.072245] 1-003c supply DVDD not found, using dummy regulator
[ 6.132124] 1-003c supply AVDD not found, using dummy regulator
bootlogd: cannot allocate pseudo tty: No such file or directory
[ 6.263086] ov5640_read_reg:write reg error:reg=300a
[ 6.268076] camera ov5640 is not found
ALSA: Restoring mixer settings...
INIT: Entering runlevel: 5
Configuring network interfaces... [ 9.162778] fec 20b4000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=20b4000.ethernet:01, irq=-1)
[ 9.202704] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
done.
Starting Xserver
Starting system message bus: dbus.
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting rpcbind daemon...done.
starting statd: [ 10.692949] fec 2188000.ethernet eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=20b4000.ethernet:00, irq=-1)
[ 10.732785] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
done
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting atd: OK
exportfs: can't open /etc/exports for reading
NFS daemon support not enabled in kernel
Starting system log daemon...0
Starting kernel log daemon...0
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon                      [ ok ]
Starting Telephony daemon
Starting Linux NFC daemon
Starting crond: OK
Running local boot scripts (/etc/rc.local).
Freescale i.MX Release Distro 4.1.15-2.1.0 ALIENTEK-IMX6U /dev/ttymxc0
ALIENTEK-IMX6U login: