请教原子关于UCOS+uCGUI后程序死机的问题？多谢了~

tianming

手上有一块板子，zet6主控，fsmc接TFT，然后呢在裸机下，TFT驱动没有问题，在Ucos下直接操作tft驱动也没有问题。但是我在UCOS+uCGUI下，就不行了，程序就死机了，根据目前的测试结果，发现在GUI_Init()中调用的LCD_Init()，再往下是调用LCD_L0_Init()，往下是LCD_INIT_CONTROLLER()这个宏定义，而这个宏定义是
#define LCD_INIT_CONTROLLER()  LCD_USER_Init() .按照上面的逻辑进行调用初始化的时候就会死机，连状态指示灯都不闪烁了。
我尝试着在LCD_Init()中不调用r |= LCD_L0_Init();而是改为直接调用LCD_USER_Init() 就可以了。
还有一个问题是，当利用上面的方法程序可以运行的时候，这个时候如果在void LCD_USER_Init(void)中定义一个变量，不管是u8、u16、u32，比如u16 Temp = 0x00;这样也会造成死机。
真是百思不得其解啊~~
首先想到的是堆栈溢出，于是改大堆栈，依旧死机。还有就是字节对齐的问题，于是在声明任务堆栈的时候前面添加了__align(8) static  OS_STK  LED_TASK_STK[LED_STK_SIZE];
可是问题依旧存在啊~~~
已经调试了很久，希望原子大哥能够帮忙解惑一下啊~~~

//RS接的A0

//LCD地址结构体

typedef struct

{

u16 LCD_REG;

u16 LCD_RAM;

} LCD_TypeDef;

   

#define LCD_BASE    ((u32)(0x6C000000 | 0x00000000))

#define LCD_LCD     ((LCD_TypeDef *) LCD_BASE)

//LCD初始化函数，根据原子模版改写

void LCD_USER_Init(void)

{

// u16 Temp = 0x00;

FSMC_NORSRAMInitTypeDef  FSMC_NORSRAMInitStructure;

FSMC_NORSRAMTimingInitTypeDef  readWriteTiming; 

FSMC_NORSRAMTimingInitTypeDef  writeTiming;

GPIO_InitTypeDef GPIO_InitStructure;

RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE |

                    RCC_APB2Periph_GPIOF | RCC_APB2Periph_GPIOG |

                    RCC_APB2Periph_AFIO, ENABLE);

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_4 | GPIO_Pin_5 |

                           GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_14 | 

                           GPIO_Pin_15;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;

GPIO_Init(GPIOD, &GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7 | GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | 

                           GPIO_Pin_11 | GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14 | 

                           GPIO_Pin_15;

GPIO_Init(GPIOE, &GPIO_InitStructure);

//设置PF0（即FSMC中的A0为RS）

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;

GPIO_Init(GPIOF, &GPIO_InitStructure);

//设置PG12（NE4 （LCD/CS）作为LCD的CS信号

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;

GPIO_Init(GPIOG, &GPIO_InitStructure); 

//背光控制引脚A1

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;

GPIO_Init(GPIOA, &GPIO_InitStructure);

GPIO_SetBits(GPIOA, GPIO_Pin_1);

//LCD_FSMCConfig

writeTiming.FSMC_AddressSetupTime = 0x00; //地址建立时间（ADDSET）为1个HCLK  

    writeTiming.FSMC_AddressHoldTime = 0x00; //地址保持时间（A

    writeTiming.FSMC_DataSetupTime = 0x03; ////数据保存时间为4个HCLK

    writeTiming.FSMC_BusTurnAroundDuration = 0x00;

    writeTiming.FSMC_CLKDivision = 0x00;

    writeTiming.FSMC_DataLatency = 0x00;

    writeTiming.FSMC_AccessMode = FSMC_AccessMode_A; //模式A 

 

    FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM4;//  这里我们使用NE4 ，也就对应BTCR[6],[7]。

    FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable; // 不复用数据地址

    FSMC_NORSRAMInitStructure.FSMC_MemoryType =FSMC_MemoryType_SRAM;// FSMC_MemoryType_SRAM;  //SRAM   

    FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;//存储器数据宽度为16bit   

    FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode =FSMC_BurstAccessMode_Disable;// FSMC_BurstAccessMode_Disable; 

    FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;

FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait=FSMC_AsynchronousWait_Disable; 

    FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;   

    FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;  

    FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable; //  存储器写使能

    FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;   

    FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Enable; // 读写使用不同的时序

    FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable; 

    FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &readWriteTiming; //读写时序

    FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &writeTiming;  //写时序

    FSMC_NORSRAMInit(&FSMC_NORSRAMInitStructure);  //初始化FSMC配置

    FSMC_NORSRAMCmd(FSMC_Bank1_NORSRAM4, ENABLE);  // 使能BANK1  

 

delay_ms(50); // delay 50 ms 

  LCD_WriteReg(0x0000,0x0001);

delay_ms(50); // delay 50 ms 

  //lcddev.id = LCD_ReadReg(0x0000);

lcddev.id= LCD_ReadReg(0x0000);

//LCD_WR_REG(0x0000); //写入要读的寄存器序号

//delay_us(5);

//Temp = (u16)(*(__IO uint32_t *)(0x6C000000 | 0x00000002));

// printf("aaa :%x\n",lcddev.id);

// printf("Counter:55\n");

 

LCD_WriteReg(0x000,0x0000);

LCD_WriteReg(0x000,0x0000);

LCD_WriteReg(0x000,0x0000);

LCD_WriteReg(0x000,0x0000);

delay_ms(15);

LCD_WriteReg(0x008,0x0808);

LCD_WriteReg(0x010,0x0010);

LCD_WriteReg(0x400,0x6200);

LCD_WriteReg(0x300,0x0c06);//GAMMA

LCD_WriteReg(0x301,0x9d0f);

LCD_WriteReg(0x302,0x0b05);

LCD_WriteReg(0x303,0x1217);

LCD_WriteReg(0x304,0x3333);

LCD_WriteReg(0x305,0x1712);

LCD_WriteReg(0x306,0x950b);

LCD_WriteReg(0x307,0x0f0d);

LCD_WriteReg(0x308,0x060c); 

LCD_WriteReg(0x309,0x0000);

LCD_WriteReg(0x011,0x0202);

LCD_WriteReg(0x012,0x0101);

LCD_WriteReg(0x013,0x0001);

LCD_WriteReg(0x007,0x0001);

LCD_WriteReg(0x100,0x0730);//BT,AP 0x0330

LCD_WriteReg(0x101,0x0237);//DC0,DC1,VC

LCD_WriteReg(0x103,0x2b00);//VDV //0x0f00

LCD_WriteReg(0x280,0x4000);//VCM

LCD_WriteReg(0x102,0x81b0);//VRH,VCMR,PSON,PON

delay_ms(15);

LCD_WriteReg(0x001,0x0100);

LCD_WriteReg(0x002,0x0100);

LCD_WriteReg(0x003,0x1030);

LCD_WriteReg(0x009,0x0001);

LCD_WriteReg(0x0C,0x0000); //MCU interface 

LCD_WriteReg(0x090,0x8000);

LCD_WriteReg(0x00f,0x0000);

LCD_WriteReg(0x210,0x0000);

LCD_WriteReg(0x211,0x00ef);

LCD_WriteReg(0x212,0x0000);

LCD_WriteReg(0x213,0x018f);

LCD_WriteReg(0x500,0x0000);

LCD_WriteReg(0x501,0x0000);

LCD_WriteReg(0x502,0x005f);

LCD_WriteReg(0x401,0x0001);

LCD_WriteReg(0x404,0x0000);

delay_ms(15);

LCD_WriteReg(0x007,0x0100);

delay_ms(15);

LCD_WriteReg(0x200,0x0000);

LCD_WriteReg(0x201,0x0000);

  delay_ms(15);

LCD_Display_Dir(1); //默认为竖屏

LCD_LED=1; //点亮背光

LCD_Clear(BLUE);

}