外部中断触发定时器

on the road · 发表于 2015-11-1 20:36:05

你好原子哥，我想用外部中断触发定时器，当按键按下时定时器开始工作，实现15秒的倒计时，现在还没按按键定时器就开始工作，倒计时到0，也不能停止，用mini

[mw_shl_code=c,true]void TIM3_Int_Init(u16 arr,u16 psc) { TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; NVIC_InitTypeDef NVIC_InitStructure; RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); //时钟使能 TIM_TimeBaseStructure.TIM_Period = arr; //设置在下一个更新事件装入活动的自动重装载寄存器周期的值计数到5000为500ms TIM_TimeBaseStructure.TIM_Prescaler =psc; //设置用来作为TIMx时钟频率除数的预分频值 10Khz的计数频率 TIM_TimeBaseStructure.TIM_ClockDivision = 0; //设置时钟分割:TDTS = Tck_tim TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上计数模式 TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); //根据TIM_TimeBaseInitStruct中指定的参数初始化TIMx的时间基数单位 TIM_ClearFlag(TIM3, TIM_FLAG_Update); TIM_ITConfig( TIM3, TIM_IT_Update ,ENABLE); NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn; //TIM3中断 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //先占优先级0级 NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //从优先级3级 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能 NVIC_Init(&NVIC_InitStructure); //根据NVIC_InitStruct中指定的参数初始化外设NVIC寄存器 TIM_Cmd(TIM3, ENABLE); //使能TIMx外设 } void TIM3_IRQHandler(void) //TIM3中断 { if (TIM_GetITStatus(TIM3, TIM_IT_Update) != RESET) //检查指定的TIM中断发生与否:TIM 中断源 { LCD_ShowString(30,150,200,16,16," "); LCD_ShowNum(40,150,T1,2,16); LED1=!LED1; T1-=1; } TIM_ClearITPendingBit(TIM3, TIM_IT_Update ); //清除TIMx的中断待处理位:TIM 中断源 void EXTIX_Init(void) { EXTI_InitTypeDef EXTI_InitStructure; NVIC_InitTypeDef NVIC_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);//外部中断，需要使能AFIO时钟 KEY_Init();//初始化按键对应io模式 //GPIOC.5 中断线以及中断初始化配置 GPIO_EXTILineConfig(GPIO_PortSourceGPIOC,GPIO_PinSource5); EXTI_InitStructure.EXTI_Line=EXTI_Line5; EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt; EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;//下降沿触发 EXTI_InitStructure.EXTI_LineCmd = ENABLE; EXTI_Init(&EXTI_InitStructure); //根据EXTI_InitStruct中指定的参数初始化外设EXTI寄存器 //GPIOA.15 中断线以及中断初始化配置 GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource15); EXTI_InitStructure.EXTI_Line=EXTI_Line15; EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt; EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling; EXTI_InitStructure.EXTI_LineCmd = ENABLE; EXTI_Init(&EXTI_InitStructure); //根据EXTI_InitStruct中指定的参数初始化外设EXTI寄存器 //GPIOA.0 中断线以及中断初始化配置 GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource0); EXTI_InitStructure.EXTI_Line=EXTI_Line0; EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt; EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising; EXTI_InitStructure.EXTI_LineCmd = ENABLE; EXTI_Init(&EXTI_InitStructure); //根据EXTI_InitStruct中指定的参数初始化外设EXTI寄存器 NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn; //使能按键所在的外部中断通道 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02; //抢占优先级2 NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x02; //子优先级1 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //使能外部中断通道 NVIC_Init(&NVIC_InitStructure); //根据NVIC_InitStruct中指定的参数初始化外设NVIC寄存器 NVIC_InitStructure.NVIC_IRQChannel = EXTI9_5_IRQn; //使能按键所在的外部中断通道 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02; //抢占优先级2， NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01; //子优先级1 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //使能外部中断通道 NVIC_Init(&NVIC_InitStructure); NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn; //使能按键所在的外部中断通道 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02; //抢占优先级2， NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00; //子优先级1 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //使能外部中断通道 NVIC_Init(&NVIC_InitStructure); } void EXTI0_IRQHandler(void) { //delay_ms(10); //消抖 //if(WK_UP==0) NVIC_InitTypeDef NVIC_InitStructure; if ( EXTI_GetITStatus(EXTI_Line0) == RESET ) { EXTI_ClearITPendingBit(EXTI_Line0); GPIO_SetBits(GPIOA , GPIO_Pin_0); NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0); //设置NVIC优先级分组 NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn; //中断通道名 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;//抢占优先级 NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //响应优先级 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //打开中断 NVIC_Init(&NVIC_InitStructure); //中断初始化 GPIO_ResetBits(GPIOA, GPIO_Pin_0); LED0=!LED0;} [/mw_shl_code]

板写的程序，您能帮我看看怎么回事吗