参考原子哥写的两个通道的输入捕获通道2有问题

usb123 · 发表于 2019-9-5 08:43:43

u8 TIM2CH1_CAPTURE_STA=0; //输入捕获状态
u16 TIM2CH1_CAPTURE_VAL; //输入捕获值
u8 TIM2CH2_CAPTURE_STA=0; //输入捕获状态
u16 TIM2CH2_CAPTURE_VAL; //输入捕获值
u8 TIM2CH3_CAPTURE_STA=0; //输入捕获状态
u16 TIM2CH3_CAPTURE_VAL; //输入捕获值
u8 TIM2CH4_CAPTURE_STA=0; //输入捕获状态
u16 TIM2CH4_CAPTURE_VAL; //输入捕获值
//定时器2通道1输入捕获配置
TIM_ICInitTypeDef TIM2_ICInitStructure;
void TIM2_Cap_Init(u16 arr,u16 psc)
{
GPIO_InitTypeDef GPIO_InitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
NVIC_InitTypeDef NVIC_InitStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); //使能TIM2时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); //使能GPIOA时钟
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3; //PA0 清除之前设置
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD; //PA0 输入
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_ResetBits(GPIOA,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3); //PA0 下拉
//初始化定时器2 TIM2
TIM_TimeBaseStructure.TIM_Period = arr; //设定计数器自动重装值
TIM_TimeBaseStructure.TIM_Prescaler =psc; //预分频器
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //设置时钟分割:TDTS = Tck_tim
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上计数模式
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure); //根据TIM_TimeBaseInitStruct中指定的参数初始化TIMx的时间基数单位
//初始化TIM通道1输入捕获参数
TIM2_ICInitStructure.TIM_Channel = TIM_Channel_1; //CC1S=01 选择输入端 IC1映射到TI1上
TIM2_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获
TIM2_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到TI1上
TIM2_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //配置输入分频,不分频
TIM2_ICInitStructure.TIM_ICFilter = 0x00; //IC1F=0000 配置输入滤波器不滤波
TIM_ICInit(TIM2, &TIM2_ICInitStructure);
//初始化TIM通道2输入捕获参数
TIM2_ICInitStructure.TIM_Channel = TIM_Channel_2; //CC1S=01 选择输入端 IC1映射到TI1上
TIM2_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获
TIM2_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到TI1上
TIM2_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //配置输入分频,不分频
TIM2_ICInitStructure.TIM_ICFilter = 0x00; //IC1F=0000 配置输入滤波器不滤波
TIM_ICInit(TIM2, &TIM2_ICInitStructure);
//中断分组初始化
NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn; //TIM2中断
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2; //先占优先级2级
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //从优先级0级
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
NVIC_Init(&NVIC_InitStructure); //根据NVIC_InitStruct中指定的参数初始化外设NVIC寄存器
TIM_ITConfig(TIM2,TIM_IT_Update|TIM_IT_CC1|TIM_IT_CC2|TIM_IT_CC3|TIM_IT_CC4,ENABLE); //允许更新中断 ,允许CC1IE捕获中断
TIM_Cmd(TIM2,ENABLE); //使能定时器2
}
//定时器5中断服务程序
void TIM2_IRQHandler(void)
{
//*******************************输入捕获通道1***********************************//
if((TIM2CH1_CAPTURE_STA&0X80)==0)//还未成功捕获
{
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET)
{
if(TIM2CH1_CAPTURE_STA&0X40)//已经捕获到高电平了
{
if((TIM2CH1_CAPTURE_STA&0X3F)==0X3F)//高电平太长了
{
TIM2CH1_CAPTURE_STA|=0X80;//标记成功捕获了一次
TIM2CH1_CAPTURE_VAL=0XFFFF;
}else TIM2CH1_CAPTURE_STA++;
}
}
if (TIM_GetITStatus(TIM2, TIM_IT_CC1) != RESET)//捕获1发生捕获事件
{
if(TIM2CH1_CAPTURE_STA&0X40) //捕获到一个下降沿
{
TIM2CH1_CAPTURE_STA|=0X80; //标记成功捕获到一次上升沿
TIM2CH1_CAPTURE_VAL=TIM_GetCapture1(TIM2);
TIM_OC1PolarityConfig(TIM2,TIM_ICPolarity_Rising); //CC1P=0 设置为上升沿捕获
}else //还未开始,第一次捕获上升沿
{
TIM2CH1_CAPTURE_STA=0; //清空
TIM2CH1_CAPTURE_VAL=0;
TIM_SetCounter(TIM2,0);
TIM2CH1_CAPTURE_STA|=0X40; //标记捕获到了上升沿
TIM_OC1PolarityConfig(TIM2,TIM_ICPolarity_Falling); //CC1P=1 设置为下降沿捕获
}
}
}
//*******************************输入捕获通道2***********************************//
if((TIM2CH2_CAPTURE_STA&0X80)==0)//还未成功捕获
{
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET)
{
if(TIM2CH2_CAPTURE_STA&0X40)//已经捕获到高电平了
{
if((TIM2CH2_CAPTURE_STA&0X3F)==0X3F)//高电平太长了
{
TIM2CH2_CAPTURE_STA|=0X80;//标记成功捕获了一次
TIM2CH2_CAPTURE_VAL=0XFFFF;
}else TIM2CH2_CAPTURE_STA++;
}
}
if (TIM_GetITStatus(TIM2, TIM_IT_CC2) != RESET)//捕获2发生捕获事件
{
if(TIM2CH2_CAPTURE_STA&0X40) //捕获到一个下降沿
{
TIM2CH2_CAPTURE_STA|=0X80; //标记成功捕获到一次上升沿
TIM2CH2_CAPTURE_VAL=TIM_GetCapture1(TIM2);
TIM_OC2PolarityConfig(TIM2,TIM_ICPolarity_Rising); //CC2P=0 设置为上升沿捕获
}else //还未开始,第一次捕获上升沿
{
TIM2CH2_CAPTURE_STA=0; //清空
TIM2CH2_CAPTURE_VAL=0;
TIM_SetCounter(TIM2,0);
TIM2CH2_CAPTURE_STA|=0X40; //标记捕获到了上升沿
TIM_OC2PolarityConfig(TIM2,TIM_ICPolarity_Falling); //CC2P=1 设置为下降沿捕获
}
}
}
TIM_ClearITPendingBit(TIM2, TIM_IT_CC1|TIM_IT_CC2|TIM_IT_CC3|TIM_IT_CC4|TIM_IT_Update); //清除中断标志位
}