战舰V3&精英TFTLCD汉字显示测试程序（从片内FLASH读取汉字点阵数据）

peng1554 · 发表于 2018-11-19 18:41:09

本帖最后由 peng1554 于 2018-11-19 18:42 编辑

有用户问战舰V3板子想利用片内FLASH显示汉字，所以基于战舰V3板子的TFTLCD液晶显示实验移植了这个程序，相比源程序，多了个TEXT文件夹，该文件夹下存放了与片内FLASH显示汉字相关函数的text.c和text.h

程序适合战舰V3&MINI，支持2.8寸、3.5寸、4.3寸和7寸V2MCU屏
利用PCtoLCD2002生成“开” “发” “板”三个点阵库并存放在片内FLASH，这三个点阵库数据存放在text.c中
[mw_shl_code=c,true]//24*24的OLED汉字点阵，包括三个汉字：开、发、板。这三个汉字的点阵库，是利用PCtoLCD2002生产的，
//软件设置的取模方式同OLED实验ASCII的取模方式一样，字体采用24*24大小，一个汉字点阵占用72字节。
const u8 LCD_HZK_TBL[3][72]=
{
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x08,0x08,0x02,0x08,0x08,0x04,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0xE0,
0x0F,0xFF,0x80,0x08,0x08,0x00,0x08,0x08,0x00,0x08,0x08,0x00,0x08,0x08,0x00,0x08,0x08,0x00,0x08,0x08,0x00,0x0F,0xFF,0xFE,
0x0F,0xFF,0xFE,0x08,0x08,0x00,0x08,0x08,0x00,0x10,0x08,0x00,0x10,0x10,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"开",0*/

{0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,0x04,0x01,0x80,0x08,0x0F,0x00,0x10,0x1C,0x80,0x60,0x00,0x81,0xC2,0x00,0x87,0x02,
0x00,0xFC,0x02,0x1F,0xF0,0x04,0x3C,0x9C,0x08,0x20,0x92,0x08,0x00,0x91,0x90,0x00,0x90,0x70,0x00,0x90,0x60,0x20,0x91,0x90,
0x10,0x93,0x18,0x1C,0x9C,0x08,0x0C,0x98,0x0C,0x00,0x80,0x04,0x01,0x00,0x06,0x01,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x00},/*"发",1*/

{0x00,0x00,0x00,0x00,0x00,0xC0,0x01,0x01,0x00,0x01,0x0E,0x00,0x01,0xF8,0x00,0x3F,0xFF,0xFE,0x21,0x20,0x00,0x01,0x10,0x02,
0x02,0x0C,0x0E,0x00,0x00,0x12,0x00,0x07,0xE4,0x0F,0xFE,0x04,0x08,0x40,0x08,0x08,0x78,0x10,0x08,0x47,0x30,0x08,0x41,0xE0,
0x10,0x41,0xE0,0x10,0x47,0x30,0x30,0x7C,0x18,0x30,0xE0,0x0C,0x10,0x00,0x0C,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00},/*"板",2*/
};[/mw_shl_code]
整个程序最重要的是LCD_Show_Font（）这个函数就是用来支持从片内FLASH读取汉字点阵库并显示在液晶上
[mw_shl_code=c,true]//在指定位置，显示一个24*24大小的汉字
//x,y :汉字的坐标
//index:汉字编号（在字库数组里面的编号）
void LCD_Show_Font(u16 x,u16 y,u8 index)
{
      u8 temp,t,t1;
      u16 y0=y;
      u8 *dzk;
      u8 csize=72;                                     //一个24*24的汉字72字节
      dzk=(u8*)LCD_HZK_TBL[index];       //得到汉字编号对应的点阵库
      for(t=0;t<csize;t++)
      {
            temp=dzk[t];                               //得到点阵数据
            for(t1=0;t1<8;t1++)                      //按照从高位到低位的顺序画点
            {
                     if(temp&0x80)LCD_Fast_DrawPoint(x,y,POINT_COLOR);
                     else LCD_Fast_DrawPoint(x,y,BACK_COLOR);
                     temp<<=1;
                     y++;
                     if((y-y0)==24)                      //对y坐标的处理，当y坐标距起始坐标差24个像素点，x坐标加1
                     {
                              y=y0;
                              x++;
                              break;
                     }
            }
      }
}[/mw_shl_code]
main.c中程序如下
[mw_shl_code=c,true] int main(void)
{
      delay_init();          //延时初始化
      NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);// 设置中断优先级分组2
      LED_Init();                         //初始化与LED连接的硬件接口
      uart_init(115200);
      LCD_Init();
      POINT_COLOR=RED;
      LCD_Show_Font(100,40,0);
      LCD_Show_Font(100,80,1);
      LCD_Show_Font(100,120,2);
      LCD_ShowString(75,180,150,24,24,"ALIENTEK");
      LCD_ShowString(75,210,150,24,24,"WarshipSTM32");

      while(1)
      {
            delay_ms(500);
            LED0=!LED0;
      }
}[/mw_shl_code]