求助，想使用COM3口，仿照com1的简单程序，用串口板接PB11和PB10进行通信，串口调试没反应

qingtenglei · 发表于 2016-8-26 13:04:47

求助，想使用COM3口，仿照com1的简单程序，用串口板接PB11和PB10进行通信，串口调试工具没反应。
void My_USART3_Init(void)
{
   GPIO_InitTypeDef  GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;

  RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3,ENABLE);//ê1ÄüUSART1ê±Öó
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB,ENABLE);

GPIO_PinAFConfig(GPIOB,GPIO_PinSource10,GPIO_AF_USART3);
GPIO_PinAFConfig(GPIOB,GPIO_PinSource11,GPIO_AF_USART3);

  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
  GPIO_Init(GPIOB, &GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
  GPIO_Init(GPIOB, &GPIO_InitStructure);

USART_InitStructure.USART_BaudRate=115200;
USART_InitStructure.USART_HardwareFlowControl=USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode=USART_Mode_Rx|USART_Mode_Tx;
USART_InitStructure.USART_Parity=USART_Parity_No;
USART_InitStructure.USART_StopBits=USART_StopBits_1;
USART_InitStructure.USART_WordLength=USART_WordLength_8b;

USART_Init(USART3,&USART_InitStructure);
USART_Cmd(USART3 ,ENABLE);

USART_ITConfig(USART3,USART_IT_RXNE,ENABLE);

NVIC_InitStructure.NVIC_IRQChannel=USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority=1;
NVIC_Init(&NVIC_InitStructure);

}
void USART3_IRQHandler(void)
{
u8 res;
if(USART_GetITStatus(USART3,USART_IT_RXNE))
{
res=USART_ReceiveData(USART3);
USART_SendData(USART3,res);
}

}

int main(void)
{

NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
My_USART3_Init();

while(1);

}

Da Wen · 发表于 2016-8-26 13:04:48

NVIC_InitStructure.NVIC_IRQChannel=USART1_IRQn;
      NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;
      NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;
      NVIC_InitStructure.NVIC_IRQChannelSubPriority=1;
      NVIC_Init(&NVIC_InitStructure);
      红色的地方