STM32F446无法进入USB HS中断

longgg

各位大哥们，我想请教一下：

我在STM32F407上，将USB FS作为HOST，将USB HS设置为FS模式，实现Device，经过测试发现，USB HS和FS都能够正常运行。

现在我把代码移植到STM32F446上，发现USB FS实现的HOST能够正常运行， 但是USB HS实现的Device，连接到电脑上，电脑没有没有任何反应，也没有任何提示信息，通过打印的信息来看，发现无法进入到USB HS的中断。

我想请问一下：都有什么原因可能会造成无法进入到USB HS中断，有人遇到过类型的情况吗，谢谢！

管脚配置：



中断配置：

longgg

管脚配置：
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB , ENABLE);
        RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_OTG_HS , ENABLE);
  
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_14 |
                                GPIO_Pin_15;
  
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
        GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
        GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
  GPIO_Init(GPIOB, &GPIO_InitStructure);  
  
  GPIO_PinAFConfig(GPIOB,GPIO_PinSource14,GPIO_AF_OTG2_FS) ;
  GPIO_PinAFConfig(GPIOB,GPIO_PinSource15,GPIO_AF_OTG2_FS) ;
  

  /* USB OTG HS ULPI clock Disabled*/
  RCC_AHB1PeriphClockLPModeCmd(RCC_AHB1Periph_OTG_HS_ULPI, DISABLE);  



中断配置：

void USB_OTG_BSP_EnableInterrupt(USB_OTG_CORE_HANDLE *pdev)
{
  NVIC_InitTypeDef NVIC_InitStructure;
  
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
#ifdef USE_USB_OTG_HS   
  NVIC_InitStructure.NVIC_IRQChannel = OTG_HS_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
#endif

#ifdef         USE_USB_OTG_FS
        NVIC_InitStructure.NVIC_IRQChannel = OTG_FS_IRQn;  
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 4;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
#endif
  
#ifdef USB_OTG_HS_DEDICATED_EP1_ENABLED
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
  NVIC_InitStructure.NVIC_IRQChannel = OTG_HS_EP1_OUT_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);  
  
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
  NVIC_InitStructure.NVIC_IRQChannel = OTG_HS_EP1_IN_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);   
#endif
}

peng1554

F446没用过，帮顶~

mathonix

老哥解决了吗